GENERAL SERVICE MANUAL INDEX DRIVES WARNING This is a controlled document. It is your responsibility to deliver this information
9 Overload Clutch GENERAL The CAMCO plunger-type output overload clutch is a reliable minimum service overload device requiring very little attention
10 3. Long Term Storage (Outdoors) for Periods up to One Year. Proceed as in (2) above with the following additions. (a) After filling the unit with o
11 5. All followers are worn. Rebuilding by factory is best remedy. 6. Output shaft to follower wheel connection is loose. Factory repair is recommend
12 Recommended Input Configuration The prime objective of a good input connection to an Index Drive is to maintain a constant shock-free velocity. Bot
13 Recommended Output Configuration The objective of a good output connection to an Index Drive is to make torque levels predictable and limited in ma
14 Cam & Limit Switch Functions Cam & Limit Switches serve two purposes: 1. Some customers desire an electrical signal somewhere during dwell
15 How to Order Parts Please refer to the Parts List applicable to your specific model as shown in the model-specific service manual. This Parts List
16 How to Return Equipment for Repair Please contact the IMC Repair Department in Wheeling, Illinois at (847) 459-5200 for a "Return Material Aut
17 Indexer Weights Right Angle Model lbs kg 301RA 15 6.8 400RA 33 15.0 401RA 55 24.9 512RA 80 36.3 662RA 160 72.6 663RAD 130 59.0 900RAD 220 99.8 1
18 Recommended Tightening Torque Values for Cap Screws SAE Grade 2 Torque Spec. (ft/lbs) SAE Grade 5 Torque Spec (ft/lbs) SAE Grade 8 Torque Spec (ft
1 Table of Contents Introduction...
19 IMPORTANT!!! Cam Follower Installation Procedure The H9 thru H32 (.287” thru 1.00” diameter) Cam Followers require a Steel Ball/Set Screw and an i
20 Table: Cam Follower Anchoring Method MODEL CAM FOLLOWER DIAMETER (INCHES) ANCHORING METHOD MINIATURE RGD/RGS H9 thru H24 .287 thru .750 BALL/
21 MODEL CAM FOLLOWER DIAMETER (INCH) INSERTION GAGE KIT 110RGD / RGS H24 .750 99A73565000000 110RGD / RGS H28 .875 99A73567000000 140RGD / R
22 MODEL CAM FOLLOWER DIAMETER (INCH) PART NUMBER 80RGD / RGS H18 .563 95A33041110000 SET SCREW 95A67373000000 STEEL BALL 80RGD / RGS H20 thru H
23 NOTES
24 NOTES
Industrial Motion Control, LLC CAMCO & FERGUSON Products 1444 South Wolf Road Wheeling, IL 60090 USA ph: 847-459-5200 toll-free: 800-645-5200 f
2 Introduction CAMCO Index Drives are engineered and manufactured to very high tolerances which necessitate careful inspection and maintenance. This m
3 Warnings and Cautions Statements in this manual preceded by the words WARNING or CAUTION and printed in italics are very important. We recommend you
4 After motion is complete the cam is considered to be in dwell for the reminder of the 360° rotation. During dwell the output of the Index Drive is s
5 Index Drive Lubrication Data OIL LEVEL CAMCO Index Drives are furnished with a "bulls-eye" type oil level sight gauge. The oil level shoul
6 Index Drive Oil Capacities (Approximate) For indexers mounted in the normal* position. Consult IMC for units not listed. Model No. US. Metric Mo
7 4. Check shaft -- remove surface nicks, burrs and grooves and look for spiral machine marks that can damage the seal lip. 5. Check shaft end -- remo
8 Gear Reducer Lubrication Data OIL LEVEL Most reducers are furnished with a "bull’s eye" type sight glass or a pipe plug to indicate oil le
Commentaires sur ces manuels